Shelby's ESP Firmware - Revision history

Jllracer55 at 01:26, 20 January 2019

2019-01-20T01:26:33Z

2019-01-20T01:24:34Z

2019-01-20T01:23:32Z

2019-01-14T00:56:14Z

2019-01-14T00:48:36Z

2019-01-14T00:48:10Z

2019-01-14T00:39:23Z

2019-01-14T00:35:17Z

2019-01-14T00:24:09Z

2019-01-14T00:22:42Z

@@ Line 56: / Line 56: @@
-[[File:Espixelfig3.jpg]]
+[[File:Espixelfig7.jpg]]
 '''Figure 7'''
-[[File:Espixelfig3.jpg]]
+[[File:Espixelfig8.jpg]]
 '''Figure 8'''
-[[File:Espixelfig3.jpg]]
+[[File:Espixelfig9.jpg]]
 '''Figure 9'''
-[[File:Espixelfig3.jpg]]
+[[File:Espixelfig10.jpg]]
 '''Figure 10'''

@@ Line 45: / Line 45: @@
 (See figures 5-10)
-[[File:Espixelfig3.jpg]]
+[[File:Espixelfig5.jpg]]
 '''Figure 5'''

← Older revision		Revision as of 00:56, 14 January 2019
Line 1:		Line 1:
−	First step in programming an ESP Module is to obtain a programmer. There are ~~both~~ programmers that already exist and can be purchased on sites like ebay or aliexpress and there are a few that have been developed by the DIY community. The programmer of choice for this article is the ESP Flashamater which was developed by dirknerkle.	+	First step in programming an ESP Module is to obtain a programmer. There are programmers that already exist and can be purchased on sites like ebay or aliexpress and there are a few that have been developed by the DIY community. The programmer of choice for this article is the ESP Flashamater which was developed by dirknerkle.
	[[File:20190113_174248.jpg]]		[[File:20190113_174248.jpg]]

← Older revision		Revision as of 00:39, 14 January 2019
Line 48:		Line 48:

	'''Figure 5'''		'''Figure 5'''
−	This is where you will enter the SSID(Wireless network name) for your wireless network, typically it is recommended to have an SSID that is different than your home wireless network that all other devices/computers are connected to. This recommendation is quite common due to the fact that it makes seeing the visibility of your show devices much easier and helps keep your home network security in check. However some do choose to have them on the same network. To find more information relating to wireless networks see the networking section of the wiki here:	+	This is where you will enter the SSID(Wireless network name) for your wireless network, typically it is recommended to have an SSID that is different than your home wireless network that all other devices/computers are connected to. This recommendation is quite common due to the fact that it makes seeing the visibility of your show devices much easier and helps keep your home network security in check. However some do choose to have them on the same network. To find more information relating to wireless networks see the networking section of the wiki here:'''[[Networking]]'''

← Older revision		Revision as of 00:35, 14 January 2019
Line 31:		Line 31:

	'''Figure 3'''		'''Figure 3'''
		+
		+
		+	Next, Open the ESPS Flash Tool File and you should see a page like this:(See Figure 4)
		+
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 4'''
		+
		+
		+	From here you will set and configure the parameters for your network and the type of device you are looking to program (Serial(DMX/Renard) or Pixel)
		+	(See figures 5-10)
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 5'''
		+	This is where you will enter the SSID(Wireless network name) for your wireless network, typically it is recommended to have an SSID that is different than your home wireless network that all other devices/computers are connected to. This recommendation is quite common due to the fact that it makes seeing the visibility of your show devices much easier and helps keep your home network security in check. However some do choose to have them on the same network. To find more information relating to wireless networks see the networking section of the wiki here:
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 6'''
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 7'''
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 8'''
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 9'''
		+
		+
		+	[[File:Espixelfig3.jpg]]
		+
		+	'''Figure 10'''